Open Access Open Access  Restricted Access Subscription or Fee Access

Optimizing the Punch Parameters for V-Bending Stainless Steel Using Response Surface Methodology Approach


(*) Corresponding author


Authors' affiliations


DOI: https://doi.org/10.15866/ireme.v18i1.23973

Abstract


Bending is a widely employed metal processing technique in manufacturing, presenting various technical challenges during the process, including the estimation of springback and bending load. In this experiment, the authors investigate the springback and bending load responses on two steel plates with different thicknesses to understand how variations in plate thickness impact these mechanical behaviors. The primary objective is to assess the effects of various punch variables on springback and bending load, aiming to optimize their calculation and yield punch values with the least springback and bending loads. This investigation involves sheet plate thicknesses of 1 and 2 millimeters. The testing parameters were defined for each variable, including punch angle (80, 85, and 90 degrees), punch radius (2, 4, and 6 millimeters), and punch travel (18.5, 19, and 19.5 millimeters). In the experiment, Response Surface Methodology (RSM) was employed to analyze punch radius, angle, and travel, in conjunction with the corresponding responses (springback and bending load). The application of RSM aimed to systematically optimize all collected data with the ultimate goal of achieving the lowest possible springback and bending load. Consequently, the determination of springback and bending load relies on the analysis of various punch variables. The test results indicate that punch angle and travel have a more pronounced impact on springback than punch radius, while conversely, punch angle and radius significantly influence the bending load.
Copyright © 2024 Praise Worthy Prize - All rights reserved.

Keywords


Punch Parameters; V-Bending; Stainless Steel; Response Surface Methodology

Full Text:

PDF


References


M. A. Suyuti, M. Iswar, and R. Nur, Effect of punch angle and punch radius on bend angle through air V-bending of sheet metal, in Innovative Science and Technology in Mechanical Engineering for Industry 4.0, December 01, 2019 2019, vol. 2187, p. 030002. [Online]. Available:
https://doi.org/10.1063/1.5138306

P. Karuppuswamy, C. Bhagyanathan, S. Sathish, and D. Elangovan, Comparisonal Analysis of "V" Punches with Various Radii and Its Impact on the Steel Material Used for Sheet Metal Operations, in Materials, Design and Manufacturing for Sustainable Environment: Select Proceedings of ICMDMSE 2022: Springer, 2022, pp. 113-121.
https://doi.org/10.1007/978-981-19-3053-9_10

S. S. Panicker, K. Jithesh, P. Sivaprasad, P. Sharma, and V. Varghese, Spring Back Investigations in Aluminium and Stainless-Steel Sheets, International Journal of Vehicle Structures & Systems (IJVSS), vol. 15, no. 6, 2023.

V. M. Magar and N. Agrawal, Process parameter optimization for spring back in steel grade sheet materials under V-bending using FEM and ANN approach, Ironmaking & Steelmaking, pp. 1-11, 2023.
https://doi.org/10.1080/03019233.2023.2210465

Tosun, M., Structural Design of 38 m Special Purpose Vessel in Aluminium Alloy, (2023) International Review of Mechanical Engineering (IREME), 17 (3), pp. 88-94.
https://doi.org/10.15866/ireme.v17i3.22669

Djamaluddin, F., Hidayat, D., Wandono, F., Ardiansyah, R., Optimization of Two-Side Door Beams Under Bending Load, (2023) International Review of Mechanical Engineering (IREME), 17 (5), pp. 213-217.
https://doi.org/10.15866/ireme.v17i5.23277

S. Thipprakmas and A. Sontamino, Spring-Back Characteristics on Bent Holed Parts in V-Die Bending Process, Advances in Materials Science and Engineering, vol. 2022, 2022.
https://doi.org/10.1155/2022/6488261

K. Khoirudin, S. Sukarman, D. Mulyadi, A. Fauzi, and N. Rahdiana, Evaluate the spring-back/spring-go phenomenon in low carbon steel sheet v-bending using an experimental method, in AIP Conference Proceedings, 2023, vol. 2706, no. 1: AIP Publishing.
https://doi.org/10.1063/5.0120397

R. Nur and M. A. Suyuti, Mini Press Tool as Learning Practical: Designing, Manufacturing, and Analysis, Journal of Industrial Engineering & Management Research, vol. 1, no. 2, pp. 9-14, 07/14 2020.
https://doi.org/10.7777/jiemar.v1i2.34

N. A. Rosli, M. R. Alkahari, M. F. bin Abdollah, S. Maidin, F. R. Ramli, and S. G. Herawan, Review on effect of heat input for wire arc additive manufacturing process, Journal of Materials Research and Technology, vol. 11, pp. 2127-2145, 2021.
https://doi.org/10.1016/j.jmrt.2021.02.002

C. Li, Z. Xu, L. Peng, and X. Lai, An electric-pulse-assisted stamping process towards springback suppression and precision fabrication of micro channels, International Journal of Mechanical Sciences, vol. 218, p. 107081, 2022/03/15/ 2022.
https://doi.org/10.1016/j.ijmecsci.2022.107081

P. K. Sharma, V. Gautam, and A. K. Agrawal, Analytical and Numerical Prediction of Springback of SS/Al-Alloy Cladded Sheet in V-Bending, Journal of Manufacturing Science and Engineering, vol. 143, no. 3, 2020.
https://doi.org/10.1115/1.4048953

S. Guo, C. Tian, H. Pan, X. Tang, L. Han, and J. Wang, Research on the Springback Behavior of 316LN Stainless Steel in Micro-Scale Bending Processes, Materials, vol. 15, no. 18, p. 6373, 2022.
https://doi.org/10.3390/ma15186373

M. S. Buang, S. A. Abdullah, and J. Saedon, Effect of Die And Punch Radius On Springback Of Stainless Steel Sheet Metal In The Air V-Die Bending Process, Journal of Mechanical Engineering and Sciences, vol. 8, pp. 1322-1331, 12/09 2022.
https://doi.org/10.15282/jmes.8.2015.7.0129

R. Ouled Ahmed Ben Ali and S. Chatti, Springback Prediction of Sandwich Panel Using Machine Learning Methods, Mechanics Of Advanced Composite Structures, vol. 10, no. 1, pp. 11-20, 2023.

M. Özdemir, Optimization of Spring Back in Air V Bending Processing using Taguchi and RSM Method, Mechanics, vol. 26, pp. 73-81, 02/12 2020.
https://doi.org/10.5755/j01.mech.26.1.22831

B. Subramanian, K. Kanagaraj, and R. Soundararajan, Experimental Study on SS 304 Sheet Metal for Bending Process Optimization using Response Surface Method, SAE Technical Paper, 0148-7191, 2021.

D. Pritima, G. Veerappan, V. D. Patel, and N. R. Parthasarathy, Analysis of spring back behaviour during bending of AISI 1045 sheet metal, Materials Today: Proceedings, vol. 59, pp. 1575-1580, 2022/01/01/ 2022.
https://doi.org/10.1016/j.matpr.2022.04.160

N. Şen and V. Taşdemir, Experimental and numerical investigation of the springback behaviour of CP800 sheet after the V-bending process, Ironmaking & Steelmaking, vol. 48, no. 7, pp. 811-818, 2021.
https://doi.org/10.1080/03019233.2021.1872466

Z. Cinar, M. Asmael, Q. Zeeshan, and B. Safaei, Effect of springback on A6061 sheet metal bending: a review, Jurnal Kejuruteraan, vol. 33, no. 1, pp. 13-26, 2021.
https://doi.org/10.17576/jkukm-2021-33(1)-02

S. Hakimi and A. Soualem, Evaluation of the sensitivity of springback to various process parameters of aluminum alloy sheet with different heat treatment conditions, Engineering Solid Mechanics, vol. 9, no. 3, pp. 323-334, 2021.
https://doi.org/10.5267/j.esm.2021.1.005

A. H. Elsheikh, H. Panchal, S. Shanmugan, T. Muthuramalingam, A. M. El-Kassas, and B. Ramesh, Recent progresses in wood-plastic composites: Pre-processing treatments, manufacturing techniques, recyclability and eco-friendly assessment, Cleaner Engineering and Technology, vol. 8, p. 100450, 2022.
https://doi.org/10.1016/j.clet.2022.100450

Q. Xu et al., Characterization and nutritional value of hydrothermal liquid products from distillers grains, Journal of Environmental Management, vol. 316, p. 115275, 2022.
https://doi.org/10.1016/j.jenvman.2022.115275

Q.-H. Trieu, G.-H. Vuong, and D.-T. Nguyen, Predictive Modeling of Spring-Back Behavior in V-Bending of SS400 Steel Sheets under Elevated Temperatures Using Combined Hardening Laws, Applied Sciences, vol. 13, no. 18, p. 10347, 2023.
https://doi.org/10.3390/app131810347

H. Li et al., Spring-back behaviors of Ti-6Al-4V sheet under effect of strain rate, International Journal of Mechanical Sciences, vol. 260, p. 108646, 2023.
https://doi.org/10.1016/j.ijmecsci.2023.108646

R. Nur, N. M. Yusof, I. Sudin, F. M. Nor, and D. Kurniawan, Determination of Energy Consumption during Turning of Hardened Stainless Steel Using Resultant Cutting Force, Metals, vol. 11, no. 4, p. 565, 2021.
https://doi.org/10.3390/met11040565

Y. Touggui, S. Belhadi, A. Uysal, M. Temmar, and M. A. Yallese, A comparative study on performance of cermet and coated carbide inserts in straight turning AISI 316L austenitic stainless steel, The International Journal of Advanced Manufacturing Technology, vol. 112, pp. 241-260, 2021.
https://doi.org/10.1007/s00170-020-06385-5

S. Thipprakmas, Spring-back factor applied for V-bending die design, Journal of Advanced Mechanical Design, Systems, and Manufacturing, vol. 14, no. 3, pp. JAMDSM0037-JAMDSM0037, 2020.
https://doi.org/10.1299/jamdsm.2020jamdsm0037

M. Wasif, S. Iqbal, M. Tufail, and H. Karim, Experimental Analysis and Prediction of Springback in V-bending Process of High-Tensile Strength Steels, Transactions of the Indian Institute of Metals, vol. 73, 11/16 2019.
https://doi.org/10.1007/s12666-019-01843-5

M. A. Wahed, A. K. Gupta, V. S. R. Gadi, S. K, S. K. Singh, and N. Kotkunde, Parameter optimisation in V-bending process at elevated temperatures to minimise spring back in Ti-6Al-4V alloy, Advances in Materials and Processing Technologies, vol. 6, no. 2, pp. 350-364, 2020/04/02 2020.
https://doi.org/10.1080/2374068X.2020.1728651

A. Badrish, A. Morchhale, N. Kotkunde, and S. Singh, Parameter Optimization in the Thermo-mechanical V-Bending Process to Minimize Springback of Inconel 625 Alloy, Arabian Journal For Science And Engineering, pp. 1-15, 02/15 2020.
https://doi.org/10.1007/s13369-020-04395-9


Refbacks

  • There are currently no refbacks.


Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize